Seagull Models MXS-R Manuel d'utilisateur Page 1

MS:128“Graphics and specifications may change without notice”.ASSEMBLY MANUALSpecifications:Wing span ----------------------------65.4in (166cm).Wing

MXS-R. Instruction Manual.10 7) Slide the fuel tank into the fuse

11www.seagullmodels.com 4) Slide the collar to the axle and setscrewthe collars to secure the collar to the axle andthen slider the wheel on the

MXS-R. Instruction Manual.12 6) Slide the threaded end of the a

13www.seagullmodels.comINSTALLING THE MAIN LANDING GEARTO FUSELAGE. 8) The blind nuts for securing the landinggear are already mounted inside the fu

MXS-R. Instruction Manual.14C/A glue.C/A glue.M4x20mm.

15www.seagullmodels.comINSTALLING THE FUSELAGE SERVOS. 1) Install the rubber grommets and brasscollets onto the throttle servo. Test fit the servoin

MXS-R. Instruction Manual.164) On the fire wall has the location f

17www.seagullmodels.comCOWLING. 1) Slide the fiberglass cowl over the en-gine and line up the back edge of the cowl withthe marks you made on the fu

MXS-R. Instruction Manual.184) On the fire wall has the location f

19www.seagullmodels.comCOWLING. 1) Slide the fiberglass cowl over the en-gine and line up the back edge of the cowl withthe marks you made on the fu

MXS-R. Instruction Manual.2INTRODUCTION.Thank you for choosing the

MXS-R. Instruction Manual.204) On the fire wall has the location f

21www.seagullmodels.comCOWLING. 1) Slide the fiberglass cowl over the en-gine and line up the back edge of the cowl withthe marks you made on the fu

MXS-R. Instruction Manual.22- Model size: .75-.90 size models- Moto

23www.seagullmodels.com3mm.4.2mm.Blink nut.4.2mm.Epoxy.M3x15mm.Epoxy.3) Attach the motor to the front of the electricmotor box using four 3mm blind n

MXS-R. Instruction Manual.24INSTALLING THE AILERON - FLAP SERVOS.Se

25www.seagullmodels.comString.Small weight.2) Place the servo between the mountingblocks and space it from the hatch. Use a pencilto mark the mountin

MXS-R. Instruction Manual.26Wing.Aileron.M2 lock nut.AILERON PUSHRO

27www.seagullmodels.comRepeat the procedure for the other aileron servo. 5) When you are satisfied with the align-ment, hold the stabilizer in plac

MXS-R. Instruction Manual.28When cutting through the covering torem

29www.seagullmodels.comINSTALLING THE VERTICAL STABILIZER.Hinge.Masking tape. 10) After the epoxy has fully cured, re-move the masking tape or T-pins

3www.seagullmodels.comADDITIONAL ITEMS REQUIRED. 0.91-1.2 2-stroke. 1.00-1.25 4-stroke. Compu

MXS-R. Instruction Manual.30ELEVATOR PUSHROD HORNINSTALLATION.Elev

31www.seagullmodels.com 4) Elevator and rudder pushrods assemblyas pictures below. 3) Thread one clevis and M2 lock nut onto each elevator contro

MXS-R. Instruction Manual.32A.Elevator pushrod.A.C/A glue.Rudder pu

33www.seagullmodels.com 1) Elevator and rudder pushrods assembly follow pictures below.1.1.2.2.Elevator.Rudder.Throttle. 2) Install servos arm to s

MXS-R. Instruction Manual.34INSTALLTION PILOT.213M2x6mm.22) A scal

35www.seagullmodels.com1 3C/A glue.M2x6mm.5) Install the canopy and secure it with M2x6mmscrews.- Apply a bead of canopy glue around the insideedge o

MXS-R. Instruction Manual.36*If possible, first attempt to balance

37www.seagullmodels.comCONTROL THROWS.Ailerons: 15mm up 20mm down.Elevator: 15mm up. 20mm down.Rudder:

MXS-R. Instruction Manual.38 7) Check the receiver antenna. It sh

MXS-R. Instruction Manual.4 8) After both ailerons are securely h

5www.seagullmodels.comHINGING THE RUDDER. Glue the rudder hinges in place using thesame techniques used to hinge the ailerons.INSTALL THE AILERONS

MXS-R. Instruction Manual.6 Install the elevator control horn using

7www.seagullmodels.com 6mm.Rudder control horn.ENGINE MOUNT INSTALLATION.1) Locate the items necessary to install theengine mount included with your

MXS-R. Instruction Manual.8+ 1.20 : 2 STROKE + 4 STROKE.Epoxy.Epo

9www.seagullmodels.comThread locker glue.Epoxy.Basa.Epoxy.Basa.Epoxy.Battery.Tie Wrap.INSTALLING THE BATTERY.Battery.