WWW.SEAGULLMODELS.COM1 MS: 195“Graphics and specications may change without notice”.Specications:Wingspan
SAVAGE CRUISERInstruction Manual.10INSTALLING THE FUSELAGE SERVOS Because the size of servos dier, you may need to adjust the size of the precut open
WWW.SEAGULLMODELS.COM11INSTALLING THE SWITCH. Install the switch into the precut hole in the side, in the fuselage.CutSwitchINSTALLING THE MAIN LANDI
SAVAGE CRUISERInstruction Manual.12322INSTALLING WHEEL PANTS TOMAIN LANDING GEAR.Wheel collar.Wheel.M3Axle.Washer.Wheel.Wheel collar.Washer.nut.--M3.W
WWW.SEAGULLMODELS.COM13MOUNTING THE ENGINE 1) Position the engine with the drive washer (145mm) forward of the rewall as shown. 2) Use a pin drill a
SAVAGE CRUISERInstruction Manual.14 9) Move the throttle stick to the closed position and move the carburetor to closed. Use a 2.5mm hex wrench to ti
WWW.SEAGULLMODELS.COM15Needle Valve 3) Install the muer and muer exten-sion onto the engine and make the cutout in the cowl for muer clearance. Co
SAVAGE CRUISERInstruction Manual.16Balsa stick. 4) Locate the plywood battery tray to the fuselage. Tighten the screws using machine screws M3x15mm t
WWW.SEAGULLMODELS.COM17 5) Attach the speed control to the side of the motor box using two-sided tape and tie wraps. Connect the appropriate leads fr
SAVAGE CRUISERInstruction Manual.18 3) Use drill bit in a pin vise to drill the mouting holes in the blocks. 4) Apply 2-3 drops of thin C/A to each
WWW.SEAGULLMODELS.COM19 9) Set the aileron hatch in place and use a Phillips screw driver to install it with four wood screws.INSTALLING THE FLAP SER
SAVAGE CRUISERInstruction Manual.2 133551022642 ank you for choosing the SAVAGE CRUISER ARTF by SEAGULL MODELS COM-PANY LTD,. e SAVAGE CRUISER was d
SAVAGE CRUISERInstruction Manual.20INSTALLING THE FLAP SERVO. Repeat the procedure for the aileron servo.INSTALLING THE HORIZONTAL STABILIZER. 1) Us
WWW.SEAGULLMODELS.COM21 When cutting through the covering to remove it, cut with only enough pressure to only cut through the covering itself. Cutting
SAVAGE CRUISERInstruction Manual.22 4) When you are sure that everything isaligned correctly, mix up a generous amount of Flash 30 Minute Epoxy. Ap-pl
WWW.SEAGULLMODELS.COM23PushrodHex Nut.Fuel Tubing.M3 clevis.M2 clevis.INSTALLING TAILWHEEL.1) Locate the items for this section of themanual.3x20 mmIN
SAVAGE CRUISERInstruction Manual.24Metal connector.Hex nut.Crimp.M3 clevis.12Cable end.11 2 2 1122INSTALLING BATTERY-RECIEVER. 1) Pl
WWW.SEAGULLMODELS.COM25Battery.Receiver.INSTALLING BATTERY-RECIEVER. 1) Locate items necessary to install pilot, seats. 2) A scale pilot is included w
SAVAGE CRUISERInstruction Manual.26Wing Bolt.INSTALLATION STRUT WING-FUSELAGE.Epoxy264x20mmEpoxyEpoxyEpoxy
WWW.SEAGULLMODELS.COM27EpoxyEpoxy3x15mm3x15mmScrew.127
SAVAGE CRUISERInstruction Manual.2812 1)It is critical that your airplane be bal-anced correctly. Improper balance will cause your plane to lose contr
WWW.SEAGULLMODELS.COM29*If possible, rst attempt to balance the model by chaning the position of the re-ceiver battery and receiver. If you are un-ab
WWW.SEAGULLMODELS.COM3..KIT CONTENTS . HINGING THE FLAP.SEA19501 FuselageSEA19502 Wing SetSEA19503 Tail SetSEA19504 Fiberglass CowlingSEA19505 Main La
SAVAGE CRUISERInstruction Manual.30FLIGHT PREPARATION.PREFLIGHT CHECK.Check the operation and direction of the el-evator, rudder, ailerons and throttl
SAVAGE CRUISERInstruction Manual.4 8) Aer both ap are securely hinged, rmly grasp the wing panel and ap to make sure the hinges are securely glued
WWW.SEAGULLMODELS.COM5 3) Slide the aileron on the wing panel until there is only a slight gap. e hinge is now centered on the wing panel and ailero
SAVAGE CRUISERInstruction Manual.6INSTALL THE. 8) Aer both ailerons are securely hinged, rmly grasp the wing panel and aileron to make sure the hing
WWW.SEAGULLMODELS.COM7INSTALL THE AILERONS CONTROL HORN.INSTALL ELEVATOR CONTROL HORNFiberglass control horn.Aileron Fiberglass cont
SAVAGE CRUISERInstruction Manual.8ENGINE MOUNT INSTALLATION.1) Locate the items necessary to install the engine mount included with your model.2) Use
WWW.SEAGULLMODELS.COM9 8) Use plywood template to hold in place the fuel tank with C/A glue to secure the fuel tank inside the fuselage. 9) Connect th
Commentaires sur ces manuels